ReportLoq supports a wide set of reports to comply with EN 14181, EN 17255, the Waste Incineration Directive and the Large Combustion Directive. The individual plant will usually only have the reports attached that are necessary to meet the plant’s reporting requirements. Therefore, there may be differences between the reports we show here and those that are actually available. Contact Olicem if the reports you need is not listed here. The following PDF\/Excel reports are supported by default in ReportLoq:<\/p>\n
Daily\/monthly\/annual reports<\/strong><\/p>\n Daily reports<\/strong><\/p>\n Monthly reports<\/strong><\/p>\n Annual reports<\/strong><\/p>\n Special reports<\/strong><\/p>\n The following PDF \/ Excel reports are examples of special reports that are supported in ReportLoq + Cloud<\/p>\n The report can be used to validate aggregated STA and LTA values in relation to their limit values and therefore appears with a confidence interval subtracted. The report always contains oven signal, filter, flow and support parameters. In addition, all components with limit values are also included. Values appear with validation text, which marks incineration stops, exceedances, replacement values and rejected intervals.<\/p>\n<\/div> The report supports, but does not include by default:<\/p>\n<\/div> Calculation of emissions year-to-date<\/p>\n<\/div><\/li><\/ul> Note:<\/p>\n<\/div> Components that are not included in the interval report can be found in the report “Interval, production”<\/p>\n<\/div><\/li> Exceeded intervals appear from the exceedance reports<\/p>\n<\/div><\/li> The report is unsuitable for tax reporting due to a deduced confidence intervals and lack of replacement of STA values on meters with outdoor time<\/p>\n<\/div><\/li><\/ul> The report calculates the number of VSTA values and at the same time shows an overview of the status of the various VSTA values. Including e.g. number of intervals with exceedances or downtime. The report calculates both the values per. time and per. component. It thus becomes possible to see which components most often have a certain status, as well as in which periods the status most often occurs. By default, the report contains:<\/p>\n<\/div> Components with limit values as well as peripheral parameters, operation and filter<\/p>\n<\/div><\/li><\/ul> The report supports, but does not include by default:<\/p>\n<\/div> Display of other components<\/p>\n<\/div><\/li><\/ul> The report can be used to form an overview of STA and LTA values for components without limit values. The report always contains the oven signal for all components other than those specified in the “Interval report”. The report is the counterpart to the Interval Report and thus constitutes the “rest” of the components. Values appear with validation text that marks rejected intervals.<\/p>\n<\/div> The report supports, but does not include by default:<\/p>\n<\/div> Calculation of emissions year-to-date<\/p>\n<\/div><\/li><\/ul> Note:<\/p>\n<\/div> The production report is not an emissions report, and is often used to form an overview of emissions without limit values or production of MW.<\/p>\n<\/div><\/li><\/ul> The report can be used as input for tax reporting and contains STA and LTA without deducting the confidence interval and with replacement of invalid values with the highest valid STA value one week back according to BEK. No. 723 of 24\/06\/2011 \u00a73. The report contains the same components as the “Interval Report”.<\/p>\n<\/div> The report supports, but does not include by default:<\/p>\n<\/div> Calculation of emissions year-to-date<\/p>\n<\/div><\/li><\/ul> Note:<\/p>\n<\/div> If you need tax reports, you can also use the tax reports, as they are based on the green values, and contain automatic conversion to kilograms.<\/p>\n<\/div><\/li> The report cannot be weighed against limit values, as the confidence interval has not been deducted<\/p>\n<\/div><\/li><\/ul> Weighted limit values are used when the limit value is the result of a weighting of at least two factors. In reality, it is often a weighting of two MW meters that are included as AMS components. The report shows the weighted limit values as they are calculated from the logged data. The limit value is calculated based on: GVRESULTS = (GVmeter1 \u00d7 MWmeter1 + GVmeter2 \u00d7 MWmeter2) : (MWmeter1+ MWmeter2) The calculated limit value is automatically used for validation and, in case of exceedances, will appear in the exceedance reports where the calculated limit value also appears. The report contains all components with weighted limit values as well as oven signal and components used for weighting. Furthermore, the report is validated, so it is easy to see which intervals are exceeded, not valid or irrelevant to the environmental reporting. Read more about weighted limit values<\/a><\/p>\n<\/div> The report supports, but does not include by default:<\/p>\n<\/div> Calculation of emissions and limit values year-to-date<\/p>\n<\/div><\/li><\/ul> Note:<\/p>\n<\/div> The report is used for limit values and can be compared with the “Interval report”. Its values are therefore with substracted confidence intervals.<\/p>\n<\/div><\/li><\/ul>\n
\n
\n
\n
\n
\n
\n
\n
\n
\n
The interval report<\/h3><\/div>
![](\"https:\/\/www.olicem.com\/wp-content\/uploads\/2022\/04\/Stack1_Affald_Interval_Daily_2022-04-12_1.png\")
<\/a><\/span><\/div><\/div>Interval, counting<\/h3><\/div>
![](\"https:\/\/www.olicem.com\/wp-content\/uploads\/2022\/04\/Stack1_Affald_Count_report__Interval_Yearly_2021-01-01_1.png\")
<\/a><\/span><\/div><\/div>The interval report, production<\/h3><\/div>
![](\"https:\/\/www.olicem.com\/wp-content\/uploads\/2022\/04\/Stack1_Affald_Interval__Production_Daily_2022-04-12_1.png\")
<\/a><\/span><\/div><\/div>Green values<\/h3><\/div>
![](\"https:\/\/www.olicem.com\/wp-content\/uploads\/2022\/04\/Stack1_Affald_Green_values_Daily_2022-04-12_1.png\")
<\/a><\/span><\/div><\/div>Weighted limit values<\/h3><\/div>
![](\"https:\/\/www.olicem.com\/wp-content\/uploads\/2022\/04\/Linje1_Intervals__weighted_limit_values_Monthly_2022-01-01_1.png\")
<\/a><\/span><\/div><\/div>